How to Apply Driveway Sealer With a Squeegee?

Applying driveway sealer with a squeegee is a simple yet effective way to protect and beautify your asphalt driveway. To start, make sure that the surface of the driveway has been thoroughly cleaned and completely dry before beginning. After mixing the sealant according to the manufacturer’s instructions, pour it along one side of the driveway in an even line.

Using a soft-bristled push broom or stiff brush, spread out the sealant evenly across about 4 feet at a time. Then use your squeegee to work from one end of this section back towards you in overlapping strokes until all of the material has been worked into place. Once complete, move down another 4 feet and repeat until you have covered your entire drive way with sealant.

Allow 12 hours for drying time before parking on it again!

• Step 1: Prepare the surface of your driveway by cleaning it with a broom and brush
• Remove any debris or dirt from the cracks in the driveway
• Fill any minor cracks with crack filler before applying sealer
• Step 2: Read instructions on sealant can for proper application instructions, including dry time and coverage area per gallon of product used
• Refer to manufacturer’s safety information as well when handling chemicals like sealants and solvents used during this process
• Step 3: Pour out some sealant onto one section of your driveway at a time, using only enough to cover an area that you feel comfortable working with quickly while still wet (it will dry fast)
• Start pouring out from one side of your pavement and move slowly across towards other end until desired amount is poured out
• Step 4: Use squeegee to spread sealant evenly over entire section in one direction, making sure all areas are covered adequately without leaving behind heavy streaks or puddles which could cause discoloration after drying occurs
• Always start spreading from outside corner first then work way inward for best results; use overlapping strokes if needed for even distribution throughout entire surface being sealed off
• Step 5: Allow sealed off portion of driveway to dry completely according to manufacturer’s suggested timeframe listed on package (usually 24-48 hours) before proceeding onto next section or trafficing sealed area again until fully cured/hardened

Credit: www.homedepot.com

Is It Better to Brush Or Squeegee Driveway Sealer?

It is generally accepted that brushing driveway sealer is the preferred method for applying a new layer of sealant. Squeegeeing can be useful in certain situations, such as when trying to apply a thicker coat of sealant or if there are areas with low traffic where even coverage isn’t necessary. However, brush application offers more control and allows you to better spread the material evenly across your driveway.

Brush application also helps ensure that any small cracks or holes in the surface are sealed effectively. Additionally, it provides a smoother finish than squeegeed applications and minimizes risks of puddling or pooling which can lead to premature deterioration of your asphalt surface over time.

What is the Best Way to Apply Driveway Sealant?

The best way to apply driveway sealant is to begin by cleaning the surface of your driveway. This includes removing any dirt, debris and weeds that may be present. Once the area is cleaned, you should then fill in any cracks or holes with a patching compound specifically designed for driveways.

Next, you will want to spray on a coat of primer before applying the sealant. The primer helps ensure better adhesion between the sealant and surface areas. Finally, carefully pour out a thick line of driveway sealer along one edge of your driveway and spread it evenly using a long-handled roller or squeegee applicator.

When finished, allow several hours for drying time before walking on or driving over the sealed area.

How Do You Stir Driveway Sealer?

Stirring driveway sealer is an important step to ensure the sealer has been properly mixed and all of the ingredients are evenly distributed. The best way to stir driveway sealer is with a paint mixer attached to your drill. Make sure you wear protective gear such as gloves, goggles, and a respirator during this process.

Start by slowly mixing the material for about two minutes until it reaches an even consistency. Once done, let it sit for 10-15 minutes before use to allow any bubbles or air pockets in the mixture to rise up and dissipate.

Can I Apply Driveway Sealer With a Roller?

Yes, it is possible to apply driveway sealer with a roller. The most important factor to consider when using a roller is that the surface must be completely dry before application in order to ensure proper adhesion. Once the surface has been prepped and dried, you can use an asphalt emulsion-based sealer or a solvent-based acrylic sealer with your roller.

Begin by pouring some of the sealant into a paint tray and then dipping your roller into it so that it is evenly coated on all sides. Start at one end of your driveway and roll the sealant out in even strokes until you reach the other end. Make sure to spread enough product onto each section so that there are no bare patches left behind – this will help prevent water from seeping through and causing damage in those areas later on down the line.

Asphalt Driveway Sealcoating Squeegee – RIDESMOOTH LLC

Best Driveway Sealer

One of the best driveway sealers on the market today is latex-ite 4.75 Gal Ultra Shield Driveway Filler and Sealer. This product offers superior protection against weather, water damage, and wear from everyday use. It’s easy to apply with a brush or roller and will last up to three years before needing re-application.

Additionally, it has an advanced polymer formula that provides excellent adhesion and flexibility for long lasting results.

Conclusion

Applying driveway sealer with a squeegee is an easy and efficient way to protect your driveway from the elements. It doesn’t require any special tools or skills, just basic knowledge of how to use a squeegee and some patience. With proper preparation, you can ensure that your driveway will look great for years to come.

Applying driveway sealer with a squeegee is an inexpensive and simple way to extend the life of your asphalt driveways and maintain their beauty.