How to Take Apart Shark Steam Mop?

If you’re like me, you love your Shark steam mop. But, after a few years of use, it may start to fall apart. Here’s how to take it apart and fix it so it works like new again.

First, unplug the mop from the power source. Next, remove the water tank by unscrewing the cap and lifting it off. Set the tank aside.

Locate the two silver screws on the bottom of the mop head. Using a Phillips head screwdriver, remove the screws and set them aside. Carefully lift the mop head off the mop body.

You may need to wiggle it a bit to get it loose. Now, you should see the steam generator. Locate the two hoses connected to the generator.

One hose will have a green clip, and the other will have a red clip.

• Unplug the Shark steam mop from the electrical outlet
• Remove the water tank from the mop by pressing the release button and lifting the tank up and away from the mop
• Turn the mop over so that the bottom is facing up
• Locate the two screws on the bottom of the mop and remove them with a Phillips head screwdriver
• Lift the bottom plate off of the mop
• Disconnect the steam hose from the heating element by pressing the release button and pulling the hose away from the element
• Remove the microfiber pads from the mop head by pressing the release buttons and pulling the pads away from the head
• Lift the mop head off of the mop
• Disconnect the power cord from the control panel by pressing the release button and pulling the cord away from the panel
• Remove the control panel from the mop body by pressing the release buttons and lifting the panel away from the body

How Do You Remove the Handle from a Shark Steam Mop?

Assuming you would like tips on how to remove the handle from a Shark steam mop: First, you will need to unplug the steam mop from the power source. Next, locate the two screws on the underside of the steam mop, near where the handle meets the mop head.

Using a Phillips head screwdriver, remove these screws. With the screws removed, you should now be able to pull the handle away from the mop head.

How Do You Clean the Inside of a Shark Steam Mop?

Assuming you are talking about the Shark Steam Mop and not a generic “shark steam mop”, here are the instructions from the Shark website on how to clean the inside of the mop:

1. Remove the dirt reservoir by pulling it straight up.

2. Pour out any water that is inside the reservoir.

3. Rinse the reservoir with clean water and let it air dry.

4. Replace the dirt reservoir by pushing it back into place.

5. Fill the reservoir with clean water and replace the cap.

6. Run the mop over a dry surface to flush out any dirt or debris that may be inside the machine.

How Do You Open a Shark Steam Cleaner?

Assuming you would like instructions on how to open the Shark steam cleaner in order to clean it:

1. Unplug the Shark steam cleaner from the electrical outlet.

2. Turn the Shark steam cleaner over so that you can see the bottom.

There will be a small knob near the center.

3. Turn the knob counterclockwise until it comes completely off.

4. Lift up the cover to reveal the inside of the Shark steam cleaner.

5. Use a soft cloth to wipe away any dirt or debris that may have accumulated on the inside.

6. Replace the cover and screw the knob back into place.

7. Plug the Shark steam cleaner back into the electrical outlet and turn it on.

How to Disassemble and Repair a Shark Steam Mop – Broken Hose \ Tube

How to Remove Handle from Shark Steam Mop S1000

If you need to remove the handle from your Shark steam mop for any reason, it’s a pretty simple process. Here’s a step-by-step guide on how to do it:

1. Locate the screws that hold the handle in place.

There are two of them, and they’re located on the underside of the handle.

2. Using a Phillips head screwdriver, remove the screws.

3. Once the screws are removed, the handle should come right off.

If it’s being stubborn, you can gently wiggle it until it comes loose.

4. That’s it! You’ve now successfully removed the handle from your Shark steam mop.

Conclusion

After reading this guide, you should now know how to take apart your Shark Steam Mop. Be sure to unplug the appliance before beginning any work. Carefully remove the water tank and locate the screw that holds the bottom plate in place. Remove the four screws holding the bottom plate using a Phillips head screwdriver. Gently lift the plate off to access the heating element. Use a flathead screwdriver to unscrew the heating element from the socket. With the heating element removed, the steam mop is now ready to be cleaned.