How to Open Shark Steam Mop Head?


You’ve seen the commercials and you’re intrigued. The Shark Steam Mop promises to make cleaning your floors easier than ever. But before you can start using it, you need to know how to open the head.

Here’s a quick and easy guide to get you started. To open the head of your Shark Steam Mop, start by locating the release button. This is usually a small, round button located near the base of the handle.

Press and hold the release button while you simultaneously pull the head of the mop away from the handle. If the head is stubborn, you may need to wiggle it a bit to release it.

  • Open the Shark steam mop head by depressing the release button on the top of the unit
  • Lift the head off of the mop handle
  • Remove the microfiber pads from the bottom of the head by peeling them off
  • Rinse the steam mop head under warm water to remove any dirt or debris
  • Allow the head to air dry before reattaching it to the mop handle
How to Open Shark Steam Mop Head?


How Do You Disassemble a Shark Steam Mop?

Assuming you are referring to the Shark Steam Mop and not a Shark vacuum: To disassemble the Shark Steam Mop, start by disconnecting the power cord from the electrical outlet. Next, unscrew the handle from the mop head.

To remove the mop head, press the release button on the neck of the mop and pull the head away from the neck. The final piece to remove is the water tank, which is located on the back of the mop. To remove the tank, press the release button and lift the tank straight up.

How Do I Clean My Shark Steam Mop Head?

If you’re like most people, you probably don’t think much about cleaning your shark steam mop head. After all, it’s just a mop, right? WRONG!

Your shark steam mop head is full of nooks and crannies that can become breeding grounds for bacteria and other nasties. So, how do you clean it? Here are some simple steps to follow:

1. Unplug your shark steam mop from the power outlet.

2. Remove the mop head from the mop body.

3. Rinse the mop head under warm, running water.

4. Squeeze the mop head to remove any excess water.

5. Place the mop head on a clean, dry towel.

6. Use a clean toothbrush or other soft-bristled brush to gently scrub the mop head, paying special attention to any nooks and crannies.

7. Rinse the mop head again under warm, running water.

8. Squeeze the mop head to remove any excess water.

9. Place the mop head in a well-ventilated area to air dry.

10. Once the mop head is dry, reattach it to the mop body and plug the mop back into the power outlet. Now you’re ready to clean your floors with a clean, fresh-smelling mop head!

How Do You Remove the Handle from a Shark Steam Scrub And Mop?

Assuming you would like tips on how to remove the handle from a Shark steam scrub and mop: First, find the two black buttons on the lower part of the handle. Press and hold both of these black buttons while simultaneously pulling the handle away from the mop head.

The handle should come right off. If the handle is being stubborn and not coming off, try using a flathead screwdriver to pry the buttons up slightly while you pull on the handle. Be careful not to damage the buttons or the handle itself.

With a little patience, the handle should come off with ease.

How to Disassemble and Repair a Shark Steam Mop – Broken Hose \ Tube

How to Put the Pad on the Shark Steam Mop

If you’re looking for a quick and easy way to clean your floors, the Shark Steam Mop is a great option. But before you can start using it, you’ll need to put the pad on the mop. Here’s a step-by-step guide to help you do just that:

1. Start by removing the old pad from the mop. If it’s attached with Velcro, simply peel it off. If it’s attached with snaps, unsnap the two bottom snaps first, then lift the pad off the mop.

2. Take your new pad and align it with the bottom of the mop. If it’s a Velcro pad, simply press it into place. If it’s a snap pad, snap the two bottom snaps first, then press the pad into place.

3. That’s it! You’re now ready to start cleaning with your Shark Steam Mop.


To open the Shark Steam Mop head, first, locate the release button on the underside of the mop head. Press and hold the release button, then twist the mop head counter-clockwise. The mop head should come off easily. If it does not, check the release button to make sure it is not jammed.

Similar Posts